ADALM100 total current specifications
I have a question on the total current specifications for the ALDALM1000 . The wiki shows +/-200mA per channel. Does that also mean a total of 200mA when using both channels together ? Like if I had...
View ArticleClik here to view.
Adalm-Pluto SDR radio ejects
I'm having the problem that my SDR must be plugged in to charge while simultaneously being connected to my computer. Otherwise, the USB ejects by itself. I have two SDRs, but only one of them is having...
View ArticleClik here to view.
lab5 RC circuit (circuits 1) question
Hi, in lab5 (circuits 1) about RC circuit and several others you use 2.5 V ground instead of 0V.Why do that?I used 0V and nothing changed.Link to lab Activity 5: Transient Response of RC Circuit...
View ArticleHow to reset ADALM Pluto to default
Out of the box, I have not seen a very clean signal in cabled loopback operation. Is there a way to reset things back to default to see if that makes a difference to the spectrum?
View ArticleList of IIO commands to bring up PlutoSDR
I'm looking for a command list/reference illustrating the use of the libiio (iio_attr, iio_readdev, etc.) to boot, configure, and control a PlutoSDR in a similar fashion to the IIO 'scope software. I'm...
View ArticleClik here to view.
ADALM1000 Programming Mode
Hi, I had downloaded Pixelpulse2 and all of the associated drivers and such, and when I plugged my ADALM1000 into my computer for the first time, the LED light went on. The device was recognized by...
View ArticlePlutoSDR Table Showing IIO Channel Mapping
Is there a table showing what each IIO channel on the ad9361-phy physically maps to? I have tried "guessing and checking" but that is not very efficient and is obviously prone to error and frustration...
View ArticlePlutoSDR Buffer Formats and DDS
I'm looking for more detailed information on the data formats necessary for the Tx buffer. I think I have the Rx buffer figured out, but the Tx buffer is not as clear. I'm trying to adapt the...
View ArticleClik here to view.
IIO Buffer Methods in C#
I will preface this by saying I'm not a programmer, I'm an RF hardware guy. I'm working to write a C# wrapper for the "useful" IIO commands needed to run the PlutoSDR, configure, transmit and receive...
View ArticlePlutoSDR Advanced Debug
I would like to control BIST, as well as other parameters that show up on the IIO 'Scope Advanced tab. I found this link:AD9361 high performance, highly integrated RF Agile Transceiver™ Linux device...
View ArticlePlutoSDR Synchronize Multiple Units
I would like to synchronize the receivers on multiple units for a MIMO type application. I have downloaded the schematic and layout files, but I was hoping there would be a few pointers here to get me...
View ArticleClik here to view.
Trigger Non-Cyclic Tx Buffer
I was looking here for information on non-cyclic buffers:About libiio [Analog Devices Wiki] But didn't see anything answering my question. I would like to fill a non-cyclic buffer once, and trigger it...
View ArticleUsing extension headers on ADALM-PLUTO
How do I use the extension headers on ADALM PLUTO? In particular,There is a UART port out of the CPU. Is it /dev/ttyS0 on the embedded linux? Is it the console or a separate serial port? I assume its...
View ArticleAD9363 Aux DAC
Hi!I want to verify the AD9363 Aux DAC1 for PA control. But when I use the ADI IIO Oscilloscope to control the pluto , it seem doesn't work well as the figures show. Can anyone to give some advice...
View ArticleClik here to view.
PlutoSDR Simultaneous Trigger DAC and ADC
Is there a way to trigger both a txbuffer.push() and an rxbuffer.refill() simultaneously or with a known fixed delay between them? Something like a deterministic interrupt or queue? It seems there is...
View ArticleClik here to view.
Confusion with ADALM Pluto & libIIO
I'm looking for clarification on how interactions with the Pluto work. If I have a windows PC with a Pluto connected via USB, then on the PC I run a program which uses the C++ libiio bindings, is the...
View ArticleClik here to view.
Using PLUTO for RFID13.56 MHz
Hi,I've learned the ADALM-PLUTO RF coverage is 325 MHz - 3.8 GHz. Is there any way of using it for RFID frequency of 13.56 MHz? If not, which solution would be suitable?
View ArticleClik here to view.
Plutosdr Hardware Test - please share your results
Hi all, Some background:I am not experienced with RF. Have good general knowledge of electronics though, and bought the pluto to learn and play with RF. I received my pluto 2 weeks ago. Connected it to...
View ArticleClik here to view.
Drivers
Hello! I'm a beginner, I already receive ADALM-PLUTO, I would like to know how can I install drivers for this device on Ubuntu ?thanks,
View ArticleUsing the ADALM-JTAGUART with Xilinx Vivado/SDK
Hi all, I've just received my ADALM-PLUTO and would like to use it to try and use it to build an ADSB Mode-S receiver. The plan is to use the Pluto as a "bare board" and implement my own design, i.e....
View Article